ABB AKD-10, Installation And Maintenance Manual

Page: 35 / 77

Aux Switch (NO contact)
Aux Switch
Aux Switch
Aux Switch (NC contact)
Aux Switch (NO contact)
Aux Switch
Aux Switch
Aux Switch (NC contact)
Aux Switch (NO contact)
Aux Switch (NC contact)
(Note 1) AUX Switch (common)
Shunt Trip (NO contact)
Shunt Trip (NC contact)
(Note 1) Shunt Trip (common)
Bell Alarm (NO contact)
Bell Alarm (NC contact)
Bell Alarm (common)
Bell Alarm (NO contact)
Bell Alarm (NC contact)
Bell Alarm (common)
Closing spring charging motor
Closing spring charging motor
Close Circuit (electric bkr)*
Close Circuit
Undervoltage or Electric
Lockout
Undervoltage or Electric
Lockout
Neutral Sensor - Tap(+)
Neutral Sensor - Common(-)
Modbus (+) comment (+)
Modbus (-) comment (-)
Zone Selectivity Interlock (In+)
Zone Selectivity Interlock (In-)
Zone Selectivity Interlock (Out+)
Zone Selectivity Interlock (Out-)
Va (Voltage Conditioner)
Vb (Voltage Conditioner)
Vc (Voltage Conditioner)
(Note2) Trip Unit Aux Power
(24 Vdc+)
(Note2) Trip Unit Aux Power
(24 Vdc-)
26
27
28
29
30
31
32
33
34
35
36
10
1
2
11
12
3
4
13
5
6
7
5
6
7
14
15
16
19
20
21
8
17
9
18
22
23
24
25
Aux Switch (NO contact)
Aux Switch
Aux Switch
Aux Switch (NC contact)
Aux Switch (NO contact)
Aux Switch
Aux Switch
Aux Switch (NC contact)
10
1
2
11
12
3
4
13
Second Shunt Trip
(Note 1) Second Shunt Trip 14
5
OR
14
5
Aux Switch (NO contact)
(Note 1) Aux Switch
Aux Switch
Aux Switch (NC contact) 6
15
8
17
Remote charge Indicator**
Remote charge Indicator**
WPS-50 Fan Motor - 120Vac (H)
WPS-50 Fan Motor - 120Vac (N)
16
7
Remote Charge NC
Remote Charge NC
Spare
Spare
Spare 9
18
19
20
21
OFLO (phase A)
OFLO (phase A) 22
23
24
25
26
27
OFLO (phase B)
OFLO (phase B)
OFLO (phase C)
OFLO (phase C)
29
30
31
32
33
34
35
36
Spare
Spare
Spare
Spare
/RELT / GFA
Output- /RELT / GFA
Input+ (RELT)
Input- (RELT)
* Remote Close Accessory on manual breaker
** Remote Charge Indicator (closing springs) applies to
E/O breakers only
Notes
1. Auxiliary switch contacts are wired out if shunt trip is not
provided.
2. 24VDC auxiliary power required for RELT.
3. This drawing shows all breaker accessories. Refer to
breaker catalog number for accessories included with
the breaker.
4. Asmall number of specially wired WavePro breakers had
a Normally Closed Remote Charge Indicator switch
contact wired out to WavePro 36 Pt secondary
disconnect points C9 & C18 for use in a motor protection
circuit in AKD-10 switchgear. This functionality is not
required by the Retrofill breaker. The NMICV timer and
MC control relay's 4 parallel contacts in the switchgear
should be eliminated from the circuit. 120VAC
continuous power should be applied to WavePro/ AKD-
10 36-point secondary disconnect terminals A8 & A17.
Table 6
Legacy Wave-Pro secondary disconnect terminals and standard connections.
A-Disc Block (left side from front) C-Disc Block (right side from front)
C