ABB 2CSYK1102C/S Product Manual Download Page 37 | Manualshive

Page: 37 / 42

background image

MYLOS

®

Building Automation |

Operation of communication objects 37

MYLOS

®

Building Automation

Operation of communication objects

According to parameter setting, this communication object can be switched by the ON, OFF or Switching input
drive. With Switching the previous value, for example “1”, is directly switched to value “0”. It is important to ensure
that the communication object can be written from the outside. Therefore cyclic sending is interrupted or is not
possible.

18

Relative dimming

Rocker switch 1

3 bit DPT_Control_
Dimming

C,W,T,U

25

Relative dimming

Rocker switch 2

3 bit DPT_Control_
Dimming

C,W,T

A long input operation via this communication object causes an adjusting command “BRIGHTER” or “DARKER”
to be sent over the bus. At the end of the command a Stop command is sent to the input.

34

Disabling LED

Rocker switch 1

1 bit DPT_Enable

C,W

35

Disabling LED

Rocker switch 2

1 bit DPT_Enable

C,W

The “Disabling Led” communication object makes it possible to enable (1) the LED so as that it switches
on or off depending on the operating mode selected from the parameters or to disable it (0) forcing it into a
continuous switching off status.

3.1.4 Shutter rocker switch

No.

Function

Object name

Type of datum

Flags

16

Disabling

Rocker switch 1

1 bit DPT_Enable

C,W

23

Disabling

Rocker switch 2

1 bit DPT_Enable

C,W,T,U

The channel circuitry can be blocked or enabled using the communication object.

A blocked channel behaves as if there was no input signal. Communication objects of the channel are still available.

17

Shutter up-down

Rocker switch 1

1 bit DPT_UpDown

C,T

24

Shutter up-down

Rocker switch 2

1 bit DPT_UpDown

C,W,T,U

This communication object sends a shutter movement control (UP or DOWN) over the bus.

18

Stop/Louvre up-down

Rocker switch 1

1 bit DPT_Step

C,T

25

Stop/Louvre up-down

Rocker switch 2

1 bit DPT_Step

C,W,T,U

Telegram value:

“0” OFF

“1” ON

According to parameter setting, this communication object can be switched by the ON, OFF or Switching input

drive. With Switching the previous value, for example “1”, is directly switched to value “0”. It is important to ensure

that the communication object can be written from the outside. Therefore cyclic sending is interrupted or is not

possible.

34

Disabling LED

Rocker switch 1

1 bit DPT_Enable

C,W

35

Disabling LED

Rocker switch 2

1 bit DPT_Enable

C,W,T

«
...
35
36
37
38
39
...
»

Summary of Contents for 2CSYK1102C/S











































Reviews:

No comments

Related manuals for 2CSYK1102C/S

D DGS-3048 DGS-3048

Brand: D-Link Pages: 3

Brand: N-Tron Pages: 2

Brand: Kramer Pages: 2

Brand: Manhattan Pages: 2

Brand: LEGRAND Pages: 2

MyPower S2300-28TC-AC

Brand: Maipu Pages: 31

Brand: Hama Pages: 2

Anaconda Switcher VK68A

Brand: X10 Pages: 2

Brand: Lindy Pages: 2

Brand: Davey Pages: 2

Brand: Pathway connectivity solutions Pages: 34

Brand: SMC Networks Pages: 2

Enova DGX 100 Series

Brand: AMX Pages: 2

Brand: Emulex Pages: 75

Brand: Kramer Pages: 4

Brand: PCB Piezotronics Pages: 31

Brand: Nortel Pages: 46

ControlZAPP CZ CEFL 10VDC

Brand: DANLERS Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands