ABB 2CSYK1102C/S Product Manual Download | Manualshive

Page: 36 / 42

background image

36 Operation of communication objects

| MYLOS

®

Building Automation

MYLOS

®

Building Automation

Operation of communication objects

17

Upper rocker switch
Switching

Rocker switch 1

1 bit DPT_Switch

C,W,T

24

Upper rocker switch
Switching

Rocker switch 2

1 bit DPT_Switch

C,W,T

Telegram value:

“0” OFF
“1” ON

According to parameter setting, this communication object can be switched by the ON, OFF or Switching input
drive. With Switching the previous value, for example “1”, is directly switched to value “0”. It is important to ensure
that the communication object can be written from the outside. Therefore cyclic sending is interrupted or is not
possible.

18

Lower rocker switch
Switching

Rocker switch 1

1 bit DPT_Switch

C,W,T

25

Lower rocker switch
Switching

Rocker switch 2

1 bit DPT_Switch

C,W,T

Telegram value:

“0” OFF
“1” ON

According to parameter setting, this communication object can be switched by the ON, OFF or Switching input
drive. With Switching the previous value, for example “1”, is directly switched to value “0”. It is important to ensure
that the communication object can be written from the outside. Therefore cyclic sending is interrupted or is not
possible.

34

Disabling LED

Rocker switch 1

1 bit DPT_Enable

C,W

35

Disabling LED

Rocker switch 2

1 bit DPT_Enable

C,W

The “Disabling Led” communication object makes it possible to enable (1) the LED so as that it switches
on or off depending on the operating mode selected from the parameters or to disable it (0) forcing it into a
continuous switching off status.

3.1.3 Dimmer rocker switch

No.

Function

Object name

Type of datum

Flags

16

Disabling

Rocker switch 1

1 bit DPT_Enable

C,W,T,U

23

Disabling

Rocker switch 2

1 bit DPT_Enable

C,W

The channel circuitry can be blocked or enabled using the communication object.

A blocked channel behaves as if there was no input signal. Communication objects of the channel are still available.

17

Switching

Rocker switch 1

1 bit DPT_Switch

C,W,T,U

24

Switching

Rocker switch 2

1 bit DPT_Switch

C,W,T

Telegram value:

“0” OFF
“1” ON

«
...
34
35
36
37
38
...
»

Summary of Contents for 2CSYK1102C/S











































Reviews:

No comments

Related manuals for 2CSYK1102C/S

Brand: D-Link Pages: 14

Brand: B&K Pages: 2

Brand: B&B Electronics Pages: 45

Brand: D-Box Pages: 27

Brand: 3Com Pages: 1133

Brand: Hansen Pages: 4

Brand: Clas Ohlson Pages: 5

TM-1-8210 Series

Brand: Eaton Pages: 3

Brand: 3onedata Pages: 2

Brand: NETGEAR Pages: 2

Brand: IPGARD Pages: 2

Brand: PABX Pages: 46

Brand: Black Box Pages: 3

Brand: LEGRAND Pages: 197

Brand: Valcom Pages: 1

Brand: Hama Pages: 32

ControlCenter-IP-XS

Brand: G&D Pages: 56

Brand: UNIARCH Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands