abaco systems PPC11A Hardware Reference Manual Download Page 104

Page: 104 / 159

104 PPC11A 6U VME Single Board Computer

Publication No. PPC11A-HRM/1

5.40

Availability/Configuration Register (Offset 0x6E8)

Bits

Description

Default

7 to 5

Reserved

000

1553 CH1 availability:

1 = CH1 is available

0 = CH1 is not available

1553 CH0 availability:

1 = CH0 is available

0 = CH0 is not available

Reports the status of the NOR Flash chip ready/busy pin.

See the NOR Flash data sheet for details of how to use this bit

N/A

Reserved

Ethernet mode indicator:

1 = ETH0 and ETH1 are configured in 10/100BASE-T mode

0 = ETH0 and ETH1 are configured in 1000BASE-T mode

When available, ETH2 and ETH3 are always 10/100/1000BASE-T

5.41

Reset Control Register (Offset 0x6E9)

Bits

Description

Default

7 to 4

Reserved

0x0

XMC site 2 reset control:

1 = Assert reset to XMC site 2

0 = De-assert reset to XMC site 2

XMC site 1 reset control:

1 = Assert reset to XMC site 1

0 = De-assert reset to XMC site 1

1 & 0

Reserved

Summary of Contents for PPC11A
































































































































































Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands

abaco systems PPC11A, Hardware Reference Manual

Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands