abaco systems PPC11A Hardware Reference Manual Download Page 40 | Manualshive

Page: 40 / 159

background image

40 PPC11A 6U VME Single Board Computer

Publication No. PPC11A-HRM/1

4.11

Ethernet

The processor provides two Ethernet ports, connected via RGMII links to two
Marvell 88E1512 PHYs, as shown below. A further two, optional Ethernet ports are
provided by two Intel I210 Ethernet Controller devices accessed via the PCIe
switches.

Figure 4-4 Ethernet PHY Block Diagram

The PHYs are isolated from the backplane using transformer-coupled magnetics.

The Ethernet ports are mapped to processor Datapath Tri-Speed Ethernet Controller
(dTSEC) interfaces within Frame Manager 2 as shown below:

Table 4-7 Processor Network Interface Mapping

Processor Module Ethernet Port PHY Address
FM2_dTSEC3

ETH0

1

FM2_dTSEC4

ETH1

3

Ethernet ports ETH0 and ETH1 are provided on the VME P2 and

P0 connectors

, as

10/100BASE-T (option PPC11A-xxxxx2xx) or 10/100/1000BASE-T
(option PPC11A-xxxxx1xx) as follows:

Table 4-8 ETH0/ETH1 Pin Mapping

10/100

Signal

1000BASE-T

Signal P2 Pin

10/100

Signal

1000BASE-T

Signal P0 Pin

ETH0_TXP

ETH0_0P

C3

ETH1_TXP

ETH1_0P

A1

ETH0_TXN

ETH0_0N

C4

ETH1_TXN

ETH1_0N

A2

ETH0_RXP

ETH0_1P

C1

ETH1_RXP

ETH1_1P

B1

ETH0_RXN

ETH0_1N

C2

ETH1_RXN

ETH1_1N

B2

ETH0_2P

C31

ETH1_2P

C1

ETH0_2N

C32

ETH1_2N

C2

ETH0_3P

C5

ETH1_3P

D1

ETH0_3N

C6

ETH1_3N

D2

See the

section for more details.

«
...
38
39
40
41
42
...
»

Summary of Contents for PPC11A
































































































































































Reviews:

No comments

Related manuals for PPC11A

Brand: Intel Pages: 89

Brand: IEI Technology Pages: 126

Brand: ASROCK Pages: 30

Brand: ASROCK Pages: 114

B85-IE35 Series

Brand: MSI Pages: 190

Brand: Gigabyte Pages: 96

Brand: Photonic Universe Pages: 6

Brand: Commell Pages: 53

Brand: Texas Instruments Pages: 20

Brand: MINATO Pages: 125

Brand: Maxim Pages: 7

Brand: Microsemi Pages: 22

Brand: Supermicro Pages: 111

Brand: TransCore Pages: 40

Brand: JETWAY Pages: 46

Brand: Gigabyte Pages: 96

Side-Power SX100/185T

Brand: SLEIPNER MOTOR AS Pages: 16

Brand: Biostar Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands