abaco systems PPC11A Hardware Reference Manual Download Page 72

Page: 72 / 159

72 PPC11A 6U VME Single Board Computer

Publication No. PPC11A-HRM/1

Offsets

Access

0x70D

Watchdog Warning Threshold High Byte

R/W

0x70E

Watchdog Maximum Threshold Low Byte

R/W

0x70F

Watchdog Maximum Threshold High Byte

R/W

0x720 to 0x72F

Scratchpad memory

R/W

Where: R/W = Read/Write

RO = Read Only

WO = Write Only.

Any locations in the range 0x600 to 0x72F not shown above are reserved.

The following sections provide the definitions for the function of each bit within a
register. All registers are configured as 8-bits wide and use the little-endian
numbering convention, i.e. bit 7 is the MSB and bit 0 is the LSB.

NOTE

To mitigate against any changes that may be required to the register set in the future, register access

should ideally be performed using operating system function calls rather than directly.

5.1

Board ID Register (Offset 0x600)

The PPC11A board ID is 0x8E.

5.2

Board Revision Register (Offset 0x601)

Bits Description

Default

7:4

Major revision (artwork):

0x1 = Rev 1

0x2 = Rev 2

etc.

0x0

3:0

Minor

revision (hardware build state):

0x0 = Rev A

0x1 = Rev B

etc.

0x0

5.3

Master FPGA Revision Register (Offset 0x60B)

Bits Description
7:4

Major revision

3:0

Minor revision

Summary of Contents for PPC11A
































































































































































Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands

abaco systems PPC11A, Hardware Reference Manual

Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands