abaco systems PPC11A Hardware Reference Manual Download Page 107

Page: 107 / 159

Publication No. PPC11A-HRM/1

Control and Status Registers 107

5.48

Flash Password Registers (Offsets 0x6F0 to 0x6F7)

This block of 8 bytes provides the NOR Flash password to host software. Byte 0 is at

offset 0x6F0 and byte 7 is at offset 0x6F7.

5.49

EEPROM DIP Switch 2 Configuration Register 1 (Offset 0x6FA)

This register returns the state of the EEPROM DIP Switch 2 Register 0 when the
PPC11A was last reset. Only 6 bits are implemented.

Bits

Description

Default

7 to 4

Reserved

0x0

VMEbus path enable:
1 = Enable second (outbound) VMEbus path

0 = Disable second (outbound) VMEbus path

This is not currently implemented

2 to 0

PMC/XMC Site 2 Geographical Address:

101

= VIO is 5V

Others = VIO is 3V3

For XMC deployment, this is connected directly to the XMC;

for PMC deployment, this controls the PMC VIO voltage

5.50

EEPROM DIP Switch 2 Configuration Register 2 (Offset 0x6FB)

EEPROM DIP Switch 2 Register 1 is not implemented.

5.51

Watchdog Registers

5.51.1 Watchdog Configuration Register (Offset 0x700)

This register is locked while the watchdog is running (bit 0 of the

Watchdog Enable

is set).

Bits

Description

Default

7 & 6

Reserved

5 & 4

Interlock configuration:

= Reserved

= Once enabled, the Watchdog can never be disabled

= Once enabled, the Watchdog can only be disabled when GPIO4 is high

= The Watchdog can be disabled without restriction

3 & 2

Reserved

Warning GDISCRETE1 assertion:

1 = Warning assertion asserts GDISCRETE1

0 = Warning assertion does not assert GDISCRETE1

Reserved

Summary of Contents for PPC11A
































































































































































Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands

abaco systems PPC11A, Hardware Reference Manual

Search results

Summary of Contents for PPC11A

Reviews:

Related manuals for PPC11A

Brands by name

Popular brands