A&D FC-50Ki, Instruction Manual

Page: 45 / 64

43
11-2. Data Output Mode 11-2. Data Output Mode 11-2. Data Output Mode 11-2. Data Output Mode
q
The data output modes and parameters are set by F-Functions in
f-06 f-06 f-06 f-06
/
07 07 07 07
/
08- 08- 08- 08-
X
as
described in the F-Function parameters, section 9.
q To control the scale using commands from an external device, refer to “
11-5. 11-5. 11-5. 11-5.
Command Mode Command Mode Command Mode Command Mode
”.
q
Refer to “
11-5. Command Mode 11-5. Command Mode 11-5. Command Mode 11-5. Command Mode
” about the output data format.
Data Out Mode ( Data Out Mode ( Data Out Mode ( Data Out Mode (
f-06
f-06 f-06
f-06
////
07
07 07
07
////
08-01
08-01 08-01
08-01
))))
q
Key Mode (
f-06/07/08-01 f-06/07/08-01 f-06/07/08-01 f-06/07/08-01
="
0
")
When the weight display is stable, data is sent by pressing the PRINT key.
The count display will blink when the data has been sent.
q
Stream Mode ( f-06 f-06 f-06 f-06
/
07 07 07 07
/
08-01 08-01 08-01 08-01 =" 1 11 1 ")
Data is sent continuously. The data-update rate is approximately 10 times per
second for
f-06 f-06 f-06 f-06
/
07 07 07 07
/
08-03 08-03 08-03 08-03 =" 2 22 2 ". This rate is same as the display-update rate. For f- f- f- f-
06 06 06 06
/
07 07 07 07
/
08-3 08-3 08-3 08-3 =" 1 11 1 " or " 2 22 2 ", the interval between continuous data is approximately 1.6
seconds.
q
Auto-print Mode A ( f-06 f-06 f-06 f-06
/
07 07 07 07
/
08-01 08-01 08-01 08-01 =" 2 22 2 ")
Data is sent if the WEIGHT display is stable at +5d (weighing display division) and
above. Next transmission can not occur until after the weight display falls below +5d.
q
Auto-print Mode B ( f-06 f-06 f-06 f-06
/
07 07 07 07
/
08-01 08-01 08-01 08-01 =" 3 33 3 ")
Data is sent if the WEIGHT display is stable at ±5d (weighing display division) and
above/below. Next transmission can not occur until after the weight display falls
between –5d and +5d.
Data to be Sent (
Data to be Sent ( Data to be Sent (
Data to be Sent (
f-06 f-06 f-06 f-06
////
07 07 07 07
////
08-02 08-02 08-02 08-02
))))
Select which data is o be sent by keying in a 0 or 1 for the data: Date / time, ID No.,
PCS (count), weight or unit weight.
Example:
Key in 0 1 1 0 0 to display 01100 , this setting would send only the
ID number and the count.
Unit weight
Weight
PCS (count)
ID
Date / time
# # # # # # #
f-06-02
&&
F?I
C o m p a r a t o r
12345678C000045678id-0 01100
!
2 3 S A M U U W ( g ) 1 2 C l e a r I D
12345670.0000045678901234567
‘
0
’ not to send data
‘
1
’ to send data