3Com LSBM1SRP1M1 Page 81 Installation Manual Download

Page: 81 / 128

Installation Manual
H3C S9500 Series Routing Switches

Chapter 5 Switch Monitoring and Maintenance

5-3

Table 5-2

Description of fan tray LEDs

LED

Status

Meaning

Steady ON

The fan tray works normally.

RUN (Green)

OFF

The fan tray is faulty.

Steady ON

The fan tray is faulty.

ALM (Red)

OFF

The fan tray works normally.

Note:

The ALM LED on the fan tray keeps ON for 2 to 3 seconds when the switch is powered

on.

If the RUN LED of the fan tray is OFF, make sure that:

The fan tray has been well seated.

All the cables connecting the fan tray and the backplane have been correctly

connected and are in good condition.

The fans are working normally.

The rotation of the fans has not been blocked.

The blank filler panels have been inserted into those LPU slots.

5.1.4 Troubleshooting LPUs

The S9500 series provide LPU

LEDs on the SRPU for the user to observe the state of

these LPUs.

Note:

For the S9502, LPU 0 to LPU 2 correspond to Slots 1 to 3 respectively.

For the S9505, LPU 0 to LPU 4 correspond to Slots 2 to 6 respectively.

For the S9508/S9508V, LPU 0 to LPU 7 correspond to Slots 0 to 3 and Slots 6 to 9

respectively.

For the S9512, LPU 0 to LPU 11 correspond to Slots 0 to 5 and Slots 8 to 13

respectively.

For the meanings of LEDs, refer to Description of LPU LEDs.

Summary of Contents for LSBM1SRP1M1

































































































































Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands

3Com LSBM1SRP1M1, Installation Manual

Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands