manualshive.com logo in svg

3Com LSBM1SRP1M1, Installation Manual

Share
Download
3Com LSBM1SRP1M1 Installation Manual Download Page 83

Installation Manual 
H3C S9500 Series Routing Switches 

Chapter 5  Switch Monitoring and Maintenance

 

5-5 

 

Figure 5-1 

Remove the PSU 

II. Removing NEPS3500-A 

Follow these steps to remove NEPS3500-A: 

1) 

Remove the 1800 W sub-PSUs. 

2) 

Remove the NEPS3500-A enclosure. 

Table 5-4 

Procedure for removing NEPS3500-A 

Step 

Sub-step 

Remove 1800 
W sub-PSUs 

1)  Press down the sub-PSU lever so that the sub-module is 

separated from the backplane (refer to Figure 5-2).  

2)  Hold the handle of the sub-PSU with one hand and the 

bottom with the other hand, and gently pull the sub-PSU out 
of the chassis along the guide rails.  

Remove the 
AC power 
enclosure 

1)  Move the power switch on the PSU to the OFF position if it is 

in the ON position. 

2)  Remove the bail latch and unplug the power cord. 
3)  Remove the captive screws on the both sides of the PSU 

panel with a Phillips screwdriver.  

4)  Hold the handle on the PSU enclosure and gently pull the 

PSU enclosure out of the chassis along the guide rails.  

 

 

Figure 5-2 

Remove the 1800W sub-PSU 

Summary of Contents for LSBM1SRP1M1

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands