3Com LSBM1SRP1M1 Installation Manual Download

Page: 58 / 128

Installation Manual
H3C S9500 Series Routing Switches

Chapter 3 Switch Installation

3-16

Note:

NEPS3500-D is similar to NEPS2000-D in appearance, as shown in Figure 3-17.

The DC PSUs shown in the above figures are not equipped with plastic cover plates.

3.7 Installing a Board

The installation procedures of SRPUs, LPUs, and service boards are almost the same.

The following section describes the installation procedure of LPUs.

3.7.1 Installation Preparations

Wear the ESD-preventive wrist strap, making sure that it is properly grounded.

Loosen the mounting screws on the blank filler panel where the SRPU is to be

installed using a Phillips screwdriver and remove the blank filler panel.

Prepare the LPU to be installed.

Note:

Put the removed blank filler panel away for future use.

The LPUs of the S9500 series are hot-swappable.

3.7.2 Installation Procedure

Follow the procedure below to install an LPU:

Turn the ejector levers on the LPU outward simultaneously with both hands, insert

the LPU straight into the chassis along the guide rails until it stops sliding (that is,

the positioning pins on the ejector levers touch the positioning holes on the

chassis).

Turn the ejector levers towards the front panel to drive the positioning pins into the

positioning holes..

Summary of Contents for LSBM1SRP1M1

































































































































Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands

3Com LSBM1SRP1M1, Installation Manual

Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands