3Com LSBM1SRP1M1 Installation Manual Download

Page: 103 / 128

Installation Manual
H3C S9500 Series Routing Switches

Chapter 5 Switch Monitoring and Maintenance

5-25

Boot ROM and host program loading is completed now.

II. Remote and local loading using TFTP

Using TFTP is similar to using FTP in remote and local loading via commands. The only

difference is that you use the

tftp get

command to download software to the switch. In

this case, the switch can only be used as a TFTP client to download the software to its

CF card from the TFTP server. The remaining steps after downloading are the same as

those of remote loading using FTP.

5.3.4 Troubleshooting Software Upgrade

These types of problems may occur during software upgrade:

I. No response from SRPU serial interface

Check whether the serial interface cable is in good condition and if its attributes are set

correctly (9600 bps).

II. Uploading configuration file or host program using FTP fails

Please check that

The configuration is correct and if the FTP server is started.

The Flash has enough space for the target files.

The FTP flag is selected and is set 0x0.

III. No configuration saving during LPU reboot

Before saving the configuration, you must check the operating status of the LPU. Do

not save the configuration during the LPU reboot. Otherwise, the configuration you

want to save may be lost.

IV. LPU program loading fails or you cannot register for a long period

Check LPU type to see if this type is supported on the current host program.

Check whether the LPU Boot ROM program matches the host program before

upgrade.

Check whether LPUs are well seated.

Insert an LPU to different slots to check whether it is OK.

Check whether the host program exists and if the current host program is the

running one.

V. Insufficient Flash memory

Empty the recycle bin when the LPU starts.

Delete the unused files in the Flash.

Summary of Contents for LSBM1SRP1M1

































































































































Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands

3Com LSBM1SRP1M1, Installation Manual

Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands