manualshive.com logo in svg

3Com LSBM1SRP1M1, Installation Manual

Share
Download
3Com LSBM1SRP1M1 Installation Manual Download Page 65

Installation Manual 
H3C S9500 Series Routing Switches 

Chapter 3  Switch Installation

 

3-23 

3.9.3  Connecting the AUX Cable 

You need an AUX cable when configuring the S9500 series with the remote modem 

dial-up approach. 

I. Introduction 

The AUX cable is an 8-core shielded cable. At one end of the cable is an 

RS-232-compliant RJ-45 connector that can be plugged into the AUX port of the switch. 

At the other end is DB-9 (male) connector. You can plug it into the DB-9 (female) port of 

the modem. The AUX cable is the same as the console cable. For details, refer to 

Figure 3-23 and Table 3-3. 

II. Connecting AUX cable 

1) 

Plug the RJ-45 connector of the AUX cable into the AUX port of the switch.  

2) 

Plug the DB-9 (male) connector at the other end into the serial port of the modem. 

3.9.4  Connecting Network Cables 

I. Introduction to RJ-45 connector 

The 10/100/1000Base-T ports of the S9500 series support MDI/MDI-X auto-sensing. 

They are connected to category-5 shielded cables or above that are equipped with 

RJ-45 connectors.  

 

Figure 3-25 

RJ-45 connector 

II. Connection procedure 

1) 

Plug one end of the network cable into the Ethernet RJ-45 port to be connected on 

the switch.  

2) 

Plug the other end of the cable into the RJ-45 port of the peer device. 

Summary of Contents for LSBM1SRP1M1

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands