3Com LSBM1SRP1M1 Installation Manual Download

Page: 64 / 128

Installation Manual
H3C S9500 Series Routing Switches

Chapter 3 Switch Installation

3-22

RJ-45

Signal

DB-9

Signal

7 DSR

4 DTR

8 CTS

7 RTS

II. Connecting the console cable

Take the following steps to connect the console cable, when configuring the switch on

the terminal.

1) Plug the DB-9 female connector of the console cable into the serial port of the

PC/terminal where the switch is to be configured.

2) Connect the RJ-45 connector of the console cable to the console port of the

switch.

Figure 3-24

Connect the console cable

Note:

The PC serial port is not hot-swappable, so you are not allowed to insert or remove the

console cable into or from the PC serial port.

When connecting the console cable, first connect the DB9 end to the PC serial port and

then the RJ45 end to the console port of the switch. And removing the console cable is

just in inverse order.

When removing the console cable, first remove the RJ-45 end and then the DB9 end.

Summary of Contents for LSBM1SRP1M1

































































































































Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands

3Com LSBM1SRP1M1, Installation Manual

Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands