3Com LSBM1SRP1M1 Installation Manual Download

Page: 86 / 128

Installation Manual
H3C S9500 Series Routing Switches

Chapter 5 Switch Monitoring and Maintenance

5-8

Figure 5-6

Install the PSU air filter (II)

5.2.3 Replacing and Cleaning the Chassis Air Filter

Caution:

You are strongly recommended to clean the chassis air filter semi-monthly to

guarantee adequate ventilation.

Now, the delivered S9502, S9505, S9508, and S9512 contain no air filter. Only the

S9508V contains an chassis air filter.

For the S9500 series except the S9508V, the procedure for replacing and

cleaning/installing the chassis air filter is the same.

I. Removing, cleaning and installing the chassis air filter of the

S9505/S9508/S9512

To remove and cleaning the chassis air filter, follow the procedure below:

1) Loosen the captive screws at the top and bottom of the air filter with a Phillips

screwdriver.

Hold the air filter at the left-rear by its upper and lower edges, pull part of it out of

the chassis, put one hand underneath the air filter to hold it, and pull it out slowly

along the guides.

Summary of Contents for LSBM1SRP1M1

































































































































Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands

3Com LSBM1SRP1M1, Installation Manual

Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands