3Com LSBM1SRP1M1 Installation Manual Download

Page: 100 / 128

Installation Manual
H3C S9500 Series Routing Switches

Chapter 5 Switch Monitoring and Maintenance

5-22

ETHERNET SUBMENU

1. Download file to SDRAM through ethernet interface and boot

2. Download file to Flash through ethernet interface

3. Download file to CF card through ethernet interface

4. Modify ethernet interface boot parameter

0. Return to main menu

Enter your choice(0-4):

IV. Upgrading software through management Ethernet port (FTP)

Introduction to FTP

The S9500 series applications can also be updated through the Ethernet port and using

FTP.

Following is the upgrading procedure, using the S9512 working as an FTP Client as an

example.

Upgrade procedure

1) Connect the Switch to the PC containing the desired file via the

management/upgrade Ethernet port. (In this case, you should know the IP

address of the PC. At the same time, connect the Switch to an external PC (that

can be the same one that contains the desired file) via the Console port.

Run FTP Server on the PC connected to the management/upgrade Ethernet port,

specify the path of the upgrading file, and set the login username and password.

Run the terminal emulation program on the PC connected to the Console port, and

boot the Switch to access the Boot menu.

4) For Steps 4 to 8, see the corresponding steps in the upgrading procedure via

TFTP for reference.

Note:

If you want to download files using FTP, please set the flags to 0x0 when setting the

Ethernet interface parameters.

After downloading the host program through the Boot menu, you must specify it as the

next boot program. In the following example, the host program is 9500.app.

MAIN MENU

1. Boot with default mode

2. Boot from Flash

3. Boot from CF card

4. Enter serial submenu

5. Enter ethernet submenu

Summary of Contents for LSBM1SRP1M1

































































































































Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands

3Com LSBM1SRP1M1, Installation Manual

Search results

Summary of Contents for LSBM1SRP1M1

Reviews:

Related manuals for LSBM1SRP1M1

Brands by name

Popular brands