2N Helios IP Configuration Manual Download Page 88

Page: 88 / 177

2N TELEKOMUNIKACE a.s., www.2n.cz

88/177

The models equipped with one digital input at least help connect an open door sensor

and signal any unauthorised door opening or door closing failure with a timeout. The

events are written into a log and read out using HTTP API (refer to the 2N

Helios IP

manual).

HTTP API

Assigned input – assign one logical input to the door open sensor.

Input mode – set the input active mode (polarity).

Unathorised door open detection – enable

signalling.

UnauthorisedDoorOpen

This event is signalled if the door opens when the electric lock is inactive.

Door open too long detection – enable

signalling. This event

DoorOpenTooLong

is signalled if the door is blocked open longer than as defined.

Maximum door open time – set the maximum door opening timeout after which
the DoorOpenTooLong state is detected.

Note

Menu Digital Inputs is available for models:

2N Helios IP Verso

2N Helios IP Vario

and

if an internal card reader is

2N Helios IP Force

installed

2N Access Unit

Summary of Contents for Helios IP


















































































































































































Search results

Summary of Contents for Helios IP

Reviews:

Related manuals for Helios IP

Brands by name

Popular brands

2N Helios IP, Configuration Manual

Search results

Summary of Contents for Helios IP

Reviews:

Related manuals for Helios IP

Brands by name

Popular brands