2N Helios IP Configuration Manual Download Page 145

Page: 145 / 177

2N TELEKOMUNIKACE a.s., www.2n.cz

145/177

5.4.10 Audio Test

The

intercoms allow you to perform periodical tests of the integrated

2N Helios IP

speaker and microphone. For the test purpose, the integrated speaker generates one

or more short beeps. The integrated microphone receives the generated tone and the

test is successful if the tone is detected correctly. The test takes approximately 4

seconds. If the test fails (which may be due to an extreme surrounding noise level, e.

g.), a new test is carried out in 10 minutes. The result of the last test can be displayed

in the intercom confirmation interface or processed by the Automation

Note

The audio test is available with the Gold or Enhanced

Audio licence only.

If a call is active when the audio test starts, the audio test will be put off
until the call is terminated. The audio test will be performed the moment
the call is terminated.

Summary of Contents for Helios IP


















































































































































































Search results

Summary of Contents for Helios IP

Reviews:

Related manuals for Helios IP

Brands by name

Popular brands

2N Helios IP, Configuration Manual

Search results

Summary of Contents for Helios IP

Reviews:

Related manuals for Helios IP

Brands by name

Popular brands