ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 78 / 282

Dimension ES-3148 User’s Guide

Chapter 7 Basic Setting

Type

This field displays

10/100M

for an Ethernet/Fast Ethernet connection and

10/100/

1000M

for Gigabit connections.

Speed/Duplex

Select the speed and the duplex mode of the Ethernet connection on this port.

Choices are

Auto

10M/Half Duplex

10M/Full Duplex

100M/Half Duplex

100M/

Full Duplex

and

1000M/Full Duplex

(for Gigabit ports only).

Selecting

Auto

(auto-negotiation) allows one port to negotiate with a peer port

automatically to obtain the connection speed and duplex mode that both ends support.

When auto-negotiation is turned on, a port on the switch negotiates with the peer

automatically to determine the connection speed and duplex mode. If the peer port

does not support auto-negotiation or turns off this feature, the switch determines the

connection speed by detecting the signal on the cable and using half duplex mode.

When the switch’s auto-negotiation is turned off, a port uses the pre-configured speed

and duplex mode when making a connection, thus requiring you to make sure that the

settings of the peer port are the same in order to connect.

Flow Control

A concentration of traffic on a port decreases port bandwidth and overflows buffer

memory causing packet discards and frame losses.

Flow Control

is used to regulate

transmission of signals to match the bandwidth of the receiving port.
The switch uses IEEE802.3x flow control in full duplex mode and backpressure flow

control in half duplex mode.
IEEE802.3x flow control is used in full duplex mode to send a pause signal to the

sending port, causing it to temporarily stop sending signals when the receiving port

memory buffers fill.
Back Pressure flow control is typically used in half duplex mode to send a "collision"

signal to the sending port (mimicking a state of packet collision) causing the sending

port to temporarily stop sending signals and resend later. Select

Flow Control

enable it.

802.1p Priority This priority value is added to incoming frames without a (802.1p) priority queue tag.

See

Priority Queue Assignment

Table 10 on page 70

for more information.

BPDU Control

Configure the way to treat BPDUs received on this port. You must activate bridging

control protocol transparency in the

Switch Setup

screen first.

Select

Peer

to process any BPDU (Bridge Protocol Data Units) received on this port.

Select

Tunnel

to forward BPDUs received on this port.

Select

Discard

to drop any BPDU received on this port.

Select

Network

to process a BPDU with no VLAN tag and forward a tagged BPDU.

Apply

Click

Apply

to save the settings.

Cancel

Click

Cancel

to reset the fields to your previous configuration.

Table 12

Port Setup (continued)

LABEL

DESCRIPTION

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды