ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 190 / 282

Dimension ES-3148 User’s Guide

188

Chapter 28 Cluster Management

28.2 Cluster Management Status

Click

Management

Cluster Management

in the navigation panel to display the following

screen.

Note:

A cluster can only have one manager.

Figure 99

Cluster Management: Status

The following table describes the labels in this screen.

Table 62

Cluster Management: Status

LABEL

DESCRIPTION

Status

This field displays the role of this switch within the cluster.

Manager
Member

(you see this if you access this screen in the cluster member switch directly

and not via the cluster manager)

None

(neither a manager nor a member of a cluster)

Manager

This field displays the cluster manager switch’s hardware MAC address.

The Number of

Member

This field displays the number of switches that make up this cluster. The following

fields describe the cluster member switches.

Index

You can manage cluster member switches via the cluster manager switch. Each

number in the

Index

column is a hyperlink leading to the cluster member switch’s web

configurator (see

Figure 100 on page 189

MacAddr

This is the cluster member switch’s hardware MAC address.

Name

This is the cluster member switch’s

System Name

Model

This field displays the model name.

Status

This field displays:

Online

(the cluster member switch is accessible)

Error

(for example the cluster member switch password was changed or the switch

was set as the manager and so left the member list, etc.)

Offline

(the switch is disconnected -

Offline

shows approximately 1.5 minutes after

the link between cluster member and manager goes down)

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды