ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 209 / 282

Dimension ES-3148 User’s Guide

Chapter 31 Introducing the Commands

207

mvr

DIsplays all MVR (Multicast VLAN

Registration) settings.

<vlan-id>

DIsplays specified MVR information.

igmp-flush

Removes all IGMP information.

mac-flush

Clears the MAC address table.

<port-num>

Removes all learned MAC address on the

specified port(s).

erase

running-config

Resets to the factory default settings.

baudrate

<1|2|3|4|5>

Changes the console port speed. Choices

are 1 (9600), 2 (19200), 3(38400), 4

(57600) and 5 (115200).

boot

config <index>

Restarts the system with the specified

configuration file.

reload

config <index>

Restarts the system and use the specified

configuration file.

write

memory

Saves current configuration to the

configuration file the switch is currently

using.

<index>

Saves current configuration to the

specified configuration file on the switch.

copy

tftp flash <ip>

<remote-file>

Restores firmware via TFTP.

tftp config <index>

Restores configuration with the specified

filename from the specified TFTP server.

running-config tftp

Backs up running configuration to the

specified TFTP server with the specified

file name.

ping <ip|host-name>

Sends Ping request to an Ethernet

device.

[vlan <vlan-

id>][..]

Sends Ping request to an Ethernet device

in the specified VLAN(s).

help

Displays command help information.

traceroute

<ip|host-name> [in-

band|out-of-

band|vlan <vlan-

id>][ttl <1-255>]

[wait <1-60>]

[queries <1-10>]

Determines the path a packet takes to a

device.

help

Displays command help information.

ssh <1|2> <[user@]dest-

ip>

Connects to an SSH server with the

specified SSH version.

[command </>]

Connects to an SSH server with the

specified SSH version and addition

commands to be executed on the server.

Table 68

Command Summary: Enable Mode (continued)

COMMAND

DESCRIPTION

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды