ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 196 / 282

Dimension ES-3148 User’s Guide

194

Chapter 29 MAC Table

29.2 Viewing the MAC Table

Click

Management

MAC Table

in the navigation panel to display the following screen.

Figure 104

MAC Table

The following table describes the labels in this screen.

Table 65

MAC Table

LABEL

DESCRIPTION

Sort by

Click one of the following buttons to display and arrange the data according to that

button type. The information is then displayed in the summary table below.

MAC

Click this button to display and arrange the data according to MAC address.

VID

Click this button to display and arrange the data according to VLAN group.

Port

Click this button to display and arrange the data according to port number.

Index

This is the incoming frame index number.

MAC Address

This is the MAC address of the device from which this incoming frame came.

VID

This is the VLAN group to which this frame belongs.

Port

This is the port from which the above MAC address was learned.

Type

This shows whether the MAC address is

dynamic

(learned by the switch) or

static

(manually entered in the

Static MAC Forwarding

screen).

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды