ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя | Manualshive

Страница: 45 / 282

background image

Dimension ES-3148 User’s Guide

Chapter 3 Hardware Overview

43

The backup power supply constantly monitors the status of the internal power supply. The
backup power supply automatically provides power to the switch in the event of a power
failure. Once the switch receives power from the backup power supply, it will not
automatically switch back to using the internal power supply even when the power is resumed.

3.2 Panel LEDs

The following table describes the LEDs on the panels.

Table 2

Front Panel LEDs

LED

COLOR STATUS

DESCRIPTION

BPS

Green

Blinking

The system is receiving power from the backup power supply.

On

The backup power supply is connected and active.

Off

The backup power supply is not ready or not active.

PWR

Green

On

The system is turned on.

Off

The system is off.

SYS

Green

Blinking

The system is rebooting and performing self-diagnostic tests.

On

The system is on and functioning properly.

Off

The power is off or the system is not ready/malfunctioning.

ALM

Red

On

There is a hardware failure.

Off

The system is functioning normally.

10

Green

Blinking

The system is transmitting/receiving to/from an Ethernet device.

On

The port is connected at 10Mbps.

Off

The port is not connected at 10Mbps or to an Ethernet device.

100

Amber

Blinking

The system is transmitting/receiving to/from an Ethernet device.

On

The port is connected at 100Mbps.

Off

The port is not connected at 100Mbps or to an Ethernet device.

Uplink Gigabit Port

1000

Green

Blinking

The system is transmitting/receiving to/from an Ethernet device.

On

The port is connected at 1000Mbps.

Off

The port is not connected at 1000Mbps or to an Ethernet device.

100

Amber

Blinking

The system is transmitting/receiving to/from an Ethernet device.

On

The port is connected at 100Mbps.

Off

The port is not connected at 100Mbps or to an Ethernet device.

GBIC Slots

LNK

Green

On

The port has a successful connection.

Off

No Ethernet device is connected to this port.

ACT

Green

Blinking

The port is receiving or transmitting data.

Gigabit Port

«
...
43
44
45
46
47
...
»

Содержание Dimension ES-3148



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dimension ES-3148

Бренд: D-Link Страницы: 14

Бренд: D-Link Страницы: 7

Бренд: D-Link Страницы: 41

Бренд: Cambium Networks Страницы: 68

Бренд: Cambium Networks Страницы: 110

Бренд: Axis Страницы: 104

Бренд: Fortinet Страницы: 20

PowerBeam AC Gen2

Бренд: Ubiquiti Страницы: 22

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

System Storage DS3200

Бренд: IBM Страницы: 2

Бренд: IDT Страницы: 207

Бренд: TP-Link Страницы: 176

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

UniFi WiFi BaseStation XG

Бренд: Ubiquiti Страницы: 19

Emotron OSTO 100

Бренд: CG Страницы: 112

ISDN SOHO Router

Бренд: AOpen Страницы: 89

Бренд: PairGain Страницы: 80

Бренд: RTS Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды