ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 225 / 282

Dimension ES-3148 User’s Guide

Chapter 31 Introducing the Commands

223

31.9.6 mvr Commands

The following table lists the

mvr

commands in configuration mode.

Table 72

mvr Commands

COMMAND

DESCRIPTION

mvr <1-4094>

Enters the MVR (Multicast

VLAN Registration)

configuration mode.

source-port <port-

list>

Sets the source port(s).
An MVR source port can send

and receive multicast traffic in a

multicast VLAN.

receiver-port <port-

list>

Sets the receiver port(s).
An MVR receiver port can only

receive multicast traffic in a

multicast VLAN.

inactive

Disables MVR settings.

mode

<dynamic|compatible>

Sets the MVR mode (

dynamic

compatible

name <name-str>

Sets the MVR name for

identification purposes.

tagged <port-list>

Sets the port(s) to tag VLAN

tags.

group <name-str>

start-address <ip>

end-address <ip>

Sets the multicast group range

for the MVR.

exit

Exist from the MVR

configuration mode.

no source-port

<port-list>

Disables the source port(s).
An MVR source port can send

and receive multicast traffic in a

multicast VLAN.

no receiver-port

<port-list>

Disables the receiver port(s).
An MVR receiver port can only

receive multicast traffic in a

multicast VLAN.

no tagged <port-

list>

Sets the port(s) to untag VLAN

tags.

no inactive

Enables MVR.

no group

Disables all MVR group

settings.

no group <name-str>

Disables the specified MVR

group setting.

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды