ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя | Manualshive

Страница: 151 / 282

background image

Dimension ES-3148 User’s Guide

Chapter 21 Policy Rule

149

C

H A P T E R

21

Policy Rule

This chapter shows you how to configure policy rules.

21.1 About Policy Rules

A classifier distinguishes traffic into flows based on the configured criteria (refer to

for more information). A policy rule ensures that a traffic flow gets the

requested treatment in the network.

21.1.1 DiffServ

DiffServ (Differentiated Services) is a class of service (CoS) model that marks packets so that
they receive specific per-hop treatment at DiffServ-compliant network devices along the route
based on the application types and traffic flow. Packets are marked with DiffServ Code Points
(DSCPs) indicating the level of service desired. This allows the intermediary DiffServ-
compliant network devices to handle the packets differently depending on the code points
without the need to negotiate paths or remember state information for every flow. In addition,
applications do not have to request a particular service or give advanced notice of where the
traffic is going.

21.1.2 DSCP and Per-Hop Behavior

DiffServ defines a new DS (Differentiated Services) field to replace the Type of Service (TOS)
field in the IP header. The DS field contains a 2-bit unused field and a 6-bit DSCP field which
can define up to 64 service levels. The following figure illustrates the DS field.

DSCP is backward compatible with the three precedence bits in the ToS octet so that non-
DiffServ compliant, ToS-enabled network device will not conflict with the DSCP mapping.

The DSCP value determines the forwarding behavior, the PHB (Per-Hop Behavior), that each
packet gets across the DiffServ network. Based on the marking rule, different kinds of traffic
can be marked for different kinds of forwarding. Resources can then be allocated according to
the DSCP values and the configured policies.

DSCP (6 bits)

Unused (2 bits)

«
...
149
150
151
152
153
...
»

Содержание Dimension ES-3148



























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dimension ES-3148

Бренд: D-Link Страницы: 5

Бренд: D-Link Страницы: 2

Бренд: Paradyne Страницы: 2

Бренд: Lanpro Страницы: 5

Бренд: Zhone Страницы: 7

Бренд: Zhone Страницы: 1

Бренд: XAVI Technologies Corp. Страницы: 71

Бренд: BSD Networks Страницы: 7

NSLU2 - Network Storage Link NAS Server

Бренд: Linksys Страницы: 64

Бренд: TRENDnet Страницы: 62

Бренд: NC-link Страницы: 20

Бренд: Aethra Страницы: 2

Бренд: ZyXEL Communications Страницы: 12

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 17

Бренд: Hamlet Страницы: 6

Бренд: ZyXEL Communications Страницы: 28

Бренд: Supero Страницы: 66

Бренд: Planet Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды