ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 159 / 282

Dimension ES-3148 User’s Guide

Chapter 22 VLAN Stacking

157

Type

is a standard Ethernet type code identifying the frame and indicates that whether the

frame carries IEEE 802.1Q tag information.

SP TPID

(Service Provider Tag Protocol

Identifier) is the service provider VLAN stacking tag type.

Many vendors use 0x8100 or

0x9100.

TPID

(Tag Protocol Identifier) is the customer IEEE 802.1Q tag.

• If the VLAN stacking port role is

Access Port

, then the switch adds the

SP TPID

tag to

all incoming frames on the service provider's edge devices (1 and 2 in the VLAN stacking
example figure).

• If the VLAN stacking port role is

Tunnel

, then the switch only adds the

SP TPID

tag to

all incoming frames on the service provider's edge devices (1 and 2 in the VLAN stacking
example figure) that have an

SP TPID

different to the one configured on the switch. (If

an incoming frame’s

SP TPID

is the same as the one configured on the switch, then the

switch will not add the tag.)

Priority

refers to the IEEE 802.1p standard that allows the service provider to prioritize traffic

based on the class of service (CoS) the customer has paid for.

• On the switch, configure priority level of inner IEEE 802.1Q tag in the

Port Setup

screen.

• "0" is the lowest priority level and "7" is the highest.

VID

is the VLAN ID.

SP VID

is the VID for the second (service provider’s) VLAN tag.

22.3.1 Frame Format

The frame format for an untagged Ethernet frame, a single-tagged 802.1Q frame (customer)
and a “double-tagged” 802.1Q frame (service provider) is shown next.

Configure the fields as circled in the switch

VLAN Stacking

screen.

Table 49

Single and Double Tagged 802.11Q Frame Format

Len/Etype Data

FCS Untagged

Ethernet frame

TPID Priority VID

Len/Etype Data

FCS IEEE 802.1Q

customer

tagged frame

DA SA

SPTPID Priority VID

TPID Priority VID

Len/Etype Data

FCS Double-tagged

frame

Table 50

802.1Q Frame

Destination Address

Priority

802.1p Priority

Source Address

Len/Etype Length and type of Ethernet frame

(SP)TPID (Service Provider) Tag Protocol IDentifier

Data

Frame data

VID

VLAN ID

FCS

Frame Check Sequence

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды