ZyXEL Communications Dimension ES-3148 Скачать руководство пользователя

Страница: 221 / 282

Dimension ES-3148 User’s Guide

Chapter 31 Introducing the Commands

219

name <port-name-

string>

Sets a name for the port(s).

Enter a descriptive name (up to

nine printable ASCII

characters).

vlan-trunking

Enables VLAN Trunking on

ports connected to other

switches or routers (but not

ports directly connected to end

users) to allow frames

belonging to unknown VLAN

groups to pass through the

switch.

flow-control

Enables interface flow control.

Flow control regulates

transmissions to match the

bandwidth of the receiving port.

bandwidth-limit

Enables bandwidth control on

the port(s).

ingress <Kbps>

Sets the maximum bandwidth

allowed for incoming traffic on

the port(s).

cir <Kbps>

Sets the guaranteed bandwidth

allowed for incoming traffic on

the port(s).

pir <Kbps>

Sets the maximum bandwidth

allowed for incoming traffic on

the port(s).

egress <Kbps>

Sets the maximum bandwidth

allowed for outgoing traffic on

the port(s).

broadcast-limit

Enables broadcast storm

control limit on the switch.

<pkt/s>

Sets how many broadcast

packets the interface receives

per second.

multicast-limit

Enables the interface multicast

limit.

<pkt/s>

Sets how many multicast

packets the interface receives

per second.

dlf-limit

Enables the Destination Lookup

Failure (DLF) limit.

<pkt/s>

Sets the interface DLF limit in

packets per second (pps).

qos priority

<0 .. 7>

Sets the quality of service

priority for an interface.

mirror

Enables port mirroring in the

interface.

Table 70

interface port-channel Commands (continued)

COMMAND

DESCRIPTION

Содержание Dimension ES-3148



























































































































































































































































































Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды

ZyXEL Communications Dimension ES-3148, Руководство пользователя

Результаты поиска

Содержание Dimension ES-3148

Отзывы:

Похожие инструкции для Dimension ES-3148

Бренды по названию

Популярные бренды