Zonex GEN III VVT Series Скачать руководство пользователя страница 39

Страница: 39 / 52

Rectangular Medium Pressure Zone Dampers (WSTMRTD)

Heavy Duty Rectangular Dimensional Data

Part Number WCD W x H

Sizes available from 8” x 8” up to 48” x 48”

2 ”

Medium Pressure Rectangular Dimensional Data

Part Number WSTMRTD W x H

Sizes available from 8” x 6” up to 24” x 20”

2 ”

5”

Zonex Systems rectangular medium pressure dampers are recommended for systems under

7.5 tons with a maximum differential static pressure of 1”. The damper is equipped with a

damper board designed to support and communicate with a Zonex wireless

programmable thermostat. These are fully modulating, power open, power close

dampers. They are constructed from heavy duty aluminum and stainless steel. The damper

is an opposed blade type that slips into a 3

1/4

- inch wide cutout in the existing duct and

attaches with screws via a duct mounting plate. The duct mounting plate is 5 inches wide. A

hat section supports a reversing 24vac, 60Hz, 2 VA motor. A magnetic clutch allows for

continuous power to the motor and longer motor life. Two set screws connect the motor to

the damper shaft, allowing quick motor replacement if necessary. Motor drive time from

full open to full close is 90 seconds.

Rectangular Heavy Duty Zone Dampers (WCD)

Zonex Systems rectangular heavy duty dampers are recommended for systems 7.5 tons or

larger with a maximum differential static pressure of 1.75”. The damper is equipped with

a damper board designed to support and communicate with a Zonex wireless

programmable thermostat. These are fully modulating, power open / power close dampers

made of 20 gauge “snap lock” steel frame with S & Drive duct connections. Allow a 16” gap

in the duct for the damper. Formed steel blade stops incorporate a gasket for quiet

operation and improved structural rigidity. Rectangular dampers under 10” in height

incorporate a single blade design. Dampers 10” or over use opposed blade design.

A full stall motor, drawing 2 VA, drives the motor from full open to full close in 90 seconds.

The rectangular zone dampers are available in either medium pressure or heavy duty. For systems under 7.5 tons,

use medium pressure dampers, (part #WSTMRTD size). For systems 7.5 tons or over, use heavy duty dampers,

(part #WCD size). Motor drive time open and close is 90 seconds.

GEN III

– VVT

Содержание GEN III VVT Series





















































Результаты поиска

Содержание GEN III VVT Series

Отзывы:

Бренды по названию

Популярные бренды

Zonex GEN III VVT Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEN III VVT Series

Отзывы:

Бренды по названию

Популярные бренды