Zonex GEN III VVT Series Скачать руководство пользователя страница 36

Страница: 36 / 52

WIRELESS REMOTE SENSOR

GEN III

– VVT

Description

The wireless remote sensor part # WRS is a microprocessor based, auto

changeover, programmable communicating zone thermostat without a

local display. The zone sensor controls modulating round, rectangular

dampers or WD-Fusers. The communicating remote sensor is used with the

GEN III-VVT zoning system.

The wireless remote sensor controls and modulates zone dampers based on

variance from set point to a position that will match the supply load to the

demand requirement. When the HVAC unit is running, if a remote sensor is

not calling or is calling for the opposite mode, its corresponding damper

fully closes. When the HVAC unit is not running, the remote sensor will

instruct its corresponding damper to go into Vent mode to provide

ventilation, if the indoor blower fan is running continuously.

The Remote Sensor provides local adjustment of +/- 2 degrees from set

point using the sensors slide pot. Auxiliary or supplemental heat sources,

i.e. base board, radiant panels, or reheat coils may also be controlled and

energized from each remote sensor if required.

Use a Monitor thermostat to set and review one or more remote sensors.

Sensor can be setup with daily schedules, priority votes and override

functions which are all programmed to the remote sensor from the Monitor

thermostat.

A Wireless Occupancy Remote Sensor is also available, and when it detects

a ﬁrst body movement it will quickly blink the LED and read the slide pot.

Battery Installation

Remove wireless remote sensor cover plate.

Install two AAA batteries provided with the wireless remote sensor.

Wireless Remote Sensor

Wireless Occupancy Remote Sensor

Procedure To Synchronize ID On Wireless Remote Sensor:

Use any a wireless LCD stat to sync up.

Hold down the button on the damper control board that is needed to pair

with the wireless remote sensor until the LED blinks.

Hold down the button on the wireless remote sensor until its LED blinks.

Go to Zone Setup by holding down Menu and Auto and select (E)

System ID and set it to what your system ID is.

While still in the Zone Setup, select (F) Stat ID and set your ID.

Continue to menu item (A) in Zone Setup to synchronize damper.

When the screen displays “Synch is completed” and both LEDs’ stop

blinking, synchronization is successful.

Remember to change the ID on the wireless LCD stat to a different ID to

avoid ID conﬂicts, because now the wireless remote sensor and the

wireless LCD stat have the same ID.

To clear the wireless ID, Remove the batteries and hold down the button while putting the batteries back in for 5 seconds.

This will reset the wireless remote sensor system ID to 0 and stat ID to 21 to avoid communication.

AAA

BB W1

REHEAT

AAA

BB W1

REHEAT

SELECT

EXIT

ZONE SETUP

E. SET SYSTEM ID

F. SET STAT ID

AAA

BB W1

REHEAT

AAA

BB W1

REHEAT

AAA

BB W1

REHEAT

AAA

BB W1

REHEAT

AAA

BB W1

REHEAT

Содержание GEN III VVT Series





















































Результаты поиска

Содержание GEN III VVT Series

Отзывы:

Бренды по названию

Популярные бренды

Zonex GEN III VVT Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание GEN III VVT Series

Отзывы:

Бренды по названию

Популярные бренды