ZOJE A9200L-D4-W-CP, Руководство по эксплуатации

Страница: 21 / 65

-12-
4）取下梭芯①，用绕线切刀④切断线。
lever ③ is pushed toward direction B, and wind
4 ) Remove bobbin ①, and trim off the thre
-ad using winding trimmer ④.
注意:
1.不进行缝制时给梭芯①绕底线时，请
点击抬压脚按键抬起压脚，然后把面线
从挑线杆孔上抽出来，把梭芯①从旋梭
2.为了防止发生安全事故，在底线卷绕
的过程中，不要碰触任何运动部件或将
物件靠在运动部件上。
Caution:
1.Click the presser foot button to raise
when no sewing is the presser foot
performed, dra w the needle thread out
of hole in the take-up lever, remove
bobbin ① o ut of rotating hook.
2.Do not touch or lean anything to an
-y running components when rolling
the bottom line,in order to avoid the
safety accident.
2.底线卷绕的调节
1）调整底线卷线量时，请拧松固定螺钉⑤
，把卷线拨杆③移动到A方向或B方向，然后再
固定螺钉⑤。A方向卷线量变少，B方向卷线量
变多。(注意：卷绕在梭芯上的底线量最多应为
梭芯容量的80%)
2）如果线不能平绕梭芯时，请拧松螺母⑥
，转动绕线夹线器，调整夹线板⑦的高度：
a.旋梭①中心和夹线板⑦中心高度一样
时为标准位置。
b.下部卷的多时，向如右图D方向移动绕
线夹线器的位置，上部卷的多时，向如右图E方
向移动绕线夹线器的位置。
1.Adjusting the bobbin thread winding
1)
Toadjustthewindingcapacityofbobbin
thread, unscrew fixing screw ⑤, set winding
lever ③ in direction A or direction B, and fix s
-crew ⑤ again. Direction A is intended for re
-duction, and direction B is intended for incre
-ase(Caution:The amount of thread wound o
-nto the bobbin should be a maximum of 80%
of the bobbin capacity).
2 )If thread cannot be wound onto the bob
-bin flatly, unscrew nut ⑥, turn the winding te
-nsion disco, and adjust the height of height
of thread gripper plate ⑦.
a.The standard position is reached onc
-e the center heights of rotating hook ① and
thread gripper plate ⑦ are identical.
b.If the winding amount on the lower pa
-rt is bigger, move the winding tension disco
-ing is over.
卷绕。
c.调整绕线夹线器到合适位置后，把固
定螺钉⑥拧紧。
3）调整底线卷绕张力时，请转动线张力螺
母⑧进行调整。
in direction D indicated in the right-hand figu
-re. If the winding amount on upper part is bi
-gger, move the winding tension disco in dire
-ction E indicated in the right-hand figure.
c.When the winding tension disco reach
-es its suitable position, screw down fixing s
-crew ⑥.
3 )Adjust the winding tension of bobbin thr
-ead by turning thread tension nut ⑧.
里卸下来后再进行。