ZIEHL-ABEGG UNIcon MODBUS Master CXE/AV, Руководство по эксплуатации, Страница: 68 / 114

9.10.2.5 Switch over input “ E1 ” / “ E2 ” , function
|
4D
|
(operation with one control cicuit)
Switch over between Input signal 1 (Analog In 1 terminal “ E1 ” ) and input signal 2 (Analog In 2 terminal
“ E2 ” ).
Contact e.g. at ditgital input “ Digital In 1 ” (depending on device type at terminals “ D1 ” - “ D1 ” or “ D1 ” -
“ 24 V ” ).
24V
D1 D1
1 0
n = 0- 100 %
0
1
Si 1
Si 2
E1
GND
E2
GND
Si 1
Si 2
26.05.2010
v_4d_umschaltung_e1_e2.vsd
Controller
Si 1 Signal 1
Si 2 Signal 2
For mode speed controller ( 1.01 ) Base setup for
“
E2 Analog In
”
:
|
1E
|
necessary.
For modes controller (from 2.01 ..) Base setup for “ E2 Analog In ” :
|
7E
|
necessary (as far as
otherwise does not occupy).
9.10.2.6 Output control circuit 2 additional to “ A2 ” on “ A1 ” , function
|
4D
|
The output for control circuit 2 is set additionally to “ A2 ” to “ A1 ” (regardless of the programmed function
for
|
A1
|
). Control circuit 1 has no output for the duration of the switching.
Contact e.g. at ditgital input “ Digital In 1 ” (depending on device type at terminals “ D1 ” - “ D1 ” or “ D1 ” -
“ 24 V ” ).
At “ D1 ” Inverting “ OFF ” the output of control circuit 2 also in fl uences output “ A1 ” when the contact is
closed.
1 0
n = 0 - 100 %
03.04.2013
v_4d_contr2_a2_or_plus_a1.vsd
0
1
Controller 1
n = 0 - 100 %
A1
A2
D1
24V
D1
Sensor 1
Controller 2
Sensor 2
9.10.2.7 Set 1/2 or Setpoint 1/2, Function
|
5D
|
For Mode Speed controller 1.01 : Switch over “ Set Intern1 ” / “ Set Intern2 ”
Contact e.g. at ditgital input “ Digital In 1 ” (depending on device type at terminals “ D1 ” - “ D1 ” or “ D1 ” -
“ 24 V ” ).
Controller
24V
D1 D1
1 0
n = 40 %
1
n = 80 %
0
- - - - -
- - - - -
11.05.2007
v_5d_vorgabe_intern_1_2.vsd
2
1
1 Setting “ Set Intern1 ” (depending on device type in: %, Hz, rpm)
2 Setting “ Set Intern2 ” (depending on device type in: %, Hz, rpm)
• “ D1 Inverting ”
=
“ OFF ”
:
“ Set Intern1 ”
at
opened contact /
“ Set Intern2 ”
at closed
contact.
• “ D1 Inverting ”
=
“ ON ”
:
“ Set Intern1 ”
at
closed contact /
“ Set Intern2 ”
at opened
contact.
Operating Instructions UNIcon MODBUS Master Programming
L-BAL-E207-GB 1723 Index 003 Part.-No.
68/114