ZepSolar Zep System I Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 56

background image

ZEP SYSTEM I INSTALLATION MANUAL

Copyright © 2012 Zep Solar, Inc.

PAGE 43 OF 50

Removing Interlocks

Interlocks can be used for thermal joints at Position #2.

If your array requires thermal expan-
sion joints (refer to the installation
instructions and site design docu-
ments), the Interlocks forming the
joint secure at Position #2.

CAUTION: Do not over- or under-

tighten. Turn to Position #2 exactly.

Loosen the fasteners by turning them CCW to Position #1.

The Flat Tool alignment mark lines up
with the mark on the Interlock when
the fastener is at Position #1.

Rock the Interlock to free the Interlock.

Hook the Flat Tool on the Interlock as
shown and pull it toward you to free
the Interlock from the PV modules.

1

2

«
...
45
46
47
48
49
...
»

Содержание Zep System I

























































Отзывы:

Нет отзывов

Похожие инструкции для Zep System I

Бренд: ABB Страницы: 2

Бренд: Haier Страницы: 58

Бренд: Febco Страницы: 4

Бренд: Cisco Страницы: 48

Бренд: Handicare Страницы: 56

Бренд: Samsung Страницы: 32

Бренд: Canarm Страницы: 3

Бренд: FAAC Страницы: 32

Бренд: National Instruments Страницы: 29

Бренд: HANYOUNG NUX Страницы: 56

Бренд: Bartlett Страницы: 7

Бренд: Zeta Страницы: 44

Бренд: Waterway Страницы: 8

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: PUTCO Страницы: 2

Бренд: I-Tork Страницы: 15

Бренд: MGC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды