ZCS 1100TL-G3 Скачать руководство пользователя страница 55

Страница: 55 / 69

1.1K~3.3KTL-G3

User manual

- 50 -

3.Soft Version

10.Safety Paras

4.Hard Version

11.MPPT Scan

5.Country

12.Power Ratio

6.Modbus Address

7.Input Mode

The user enters the main menu by long pressing the button, short press and

turns the page to select menu contents, then long press the button to enter "3.

SystemInfo". Turning the page down can select the system information to view.

(D)

Display Time

Long press the button and short press the button to turn the page in the

standard user interface to enter into “4.Display Time”,then long press the button to

display the current system time.

(E)

Software Update

User can update software by USB flash drive , Our company will provide the

new update software called firmware for user if it is necessary,The user needs to

copy the upgrade file to the USB flash drive.

6.4.

Update Software online

1.1K~3.3KTL-G3 inverters offer software upgrade via usb flash drive to

maximize inverter performance and avoid inverter operation error caused by

software bugs.

Procedure:

Step 1

First,turn off the DC and AC breaker,and then remove the

communication waterproof cover as the following picture.If the RS485 line has

been connected,Be sure to release the waterproof nut,Make sure the communication

line is no longer the force. Then remove the waterproof cover,In order to avoid

loosening the communication plug which has been connected.

Figure 6-1

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды