ZCS 1100TL-G3 Скачать руководство пользователя страница 25

Страница: 25 / 69

1.1K~3.3KTL-G3

User manual

- 20 -

Interface

DVC

PV input interface

DVCC

AC output interface

DVCC

USB interface

DVCA

RS485 interface

DVCA

CT interface

DVCA

Logic interface

DVCA

WiFi/GPRS/Ethernet interface

DVCA

4.1.

Electrical connection

Figure4-1 Shows the flowchart for connecting cables to the inverter.

4.2.

Connecting PGND Cables

Connect the inverter to the grounding electrode using protection ground

(PGND) cables for grounding purpose.

The inverter is transformer-less, requires the positive pole and negative

pole of the PV array are NOT grounded. Otherwise it will cause inverter

failure. In the PV power system, all non current carrying metal parts

(such as: PV module frame, PV rack, combiner box enclosure, inverter

enclosure) should be connected to earth.

Attention

Prerequisites:

The PGND cables are prepared (

≥

4mm

outdoor power cables are

recommended for grounding purposes),the color of cable should be yellow-green.

Start

Connect PGND

cable

Connect DC

input cable

End

Connect AC output

power cable

Connect communication

cables (not mandatory)

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды