ZCS 1100TL-G3 Скачать руководство пользователя страница 10

Страница: 10 / 69

1.1K~3.3KTL-G3

User manual

- 5 -

Ensure input DC voltage < Max. DC voltage .Over voltage may

cause permanent damage to inverter or other losses, which will not
be included in warranty!

Warning

Signs on the inverter

There are some symbols which are related to security on the inverter. Please

read and understand the content of the symbols, and then start the installation.

There is a residual voltage in the inverter! Before opening the

equipment, operator should wait for five minutes to ensure the
capacitor is discharged completely.

Caution, risk of electric shock.

Caution hot surface.

Comply with the Conformite Europeenne (CE) certification.

Grounding point.

Please read this manual before install 1.1K~3.3KTL-G3.

This indicates the degree of protection of the equipment

according to IEC standard 70-1 (EN 60529 June 1997).

Positive pole and negative pole of the input voltage (DC).

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды