ZCS 1100TL-G3 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 69

background image

1.1K~3.3KTL-G3

User manual

- 57 -

is too high

ID83

Remote Derating

The inverter has
derated by the
Remote control

Inverter records ID83 in case of remote

power derating operation. Check the wiring of
remote input and output control signal port on
the communication board according to Section
4.5 of this user manual.

ID84

Remote Off

The inverter has
shut down because
by the Remote
control

Inverter records ID84 in case of remote

shutdown operation. Check the wiring of remote
input and output control signal port on the
communication board according to Section 4.5 of
this user manual.

ID94

Software version

is not consistent

The software
between the control
board and the
communication
board is not
consistent

Contact technical support to upgrade

software.

ID95

Communication

board EEPROM

fault

The
communication
board EEPROM is
fault

ID95~ID96 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,
then turn ON the “DC switch”. Check whether
the fault is rectified. If no, please contact
technical support.

ID96

RTC clock chip

anomaly

RTC clock chip is
fault

ID97

Invalid Country

The country is
invalid

Check the country setting according to

Section 6.3 (C) 5.Country of this user manual, If
it’s incorrect, change it according to Section 6.3
(A) 4.Set Country Code of this manual.

ID98

SD fault

The SD card is
fault

Please replace the SD card.

7.2.

Maintenance

Inverters generally do not need any daily or routine maintenance. Heat sink

should not be blocked by dust, dirt or any other items.Before the cleaning, make

sure that the DC SWITCH is turned OFF and the circuit breaker between inverter

and electrical grid is turned OFF. Wait at least for 5 minutes before the Cleaning.



Inverter cleaning

Please clean the inverter with an air blower, a dry & soft cloth or a soft bristle

brush. Do NOT clean the inverter with water, corrosive chemicals, detergent, etc.



Heat sink cleaning

For the long-term proper operation of inverters, ensure there is enough space

«
...
60
61
62
63
64
...
»

Содержание 1100TL-G3






































































Отзывы:

Нет отзывов

Похожие инструкции для 1100TL-G3

Бренд: Patton electronics Страницы: 16

Бренд: Danfoss Страницы: 36

Бренд: Samlexpower Страницы: 2

Бренд: Waeco Страницы: 7

Бренд: Ross Страницы: 2

Бренд: Axis Страницы: 40

Бренд: TRUlink Страницы: 15

Evershine TLC4000

Бренд: Zeversolar Страницы: 74

Бренд: Tektronix Страницы: 132

PP4000 AC PowerPack

Бренд: Lorentz Страницы: 2

Extron Electonics YCV 100

Бренд: CAMBOARD Страницы: 12

Бренд: SAJ Страницы: 61

CONVERTER DC-AC

Бренд: CARPOINT Страницы: 7

Бренд: AJA Страницы: 47

Бренд: Johnson Controls Страницы: 8

Бренд: Anttron Страницы: 12

Бренд: Transition Networks Страницы: 5

Бренд: SRS Lighting Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды