ZCS 1100TL-G3 Скачать руководство пользователя страница 56

Страница: 56 / 69

1.1K~3.3KTL-G3

User manual

- 51 -

Step 2

Insert the usb flash drive into the compute.

Step 3

Zucchetti Centro Sistemi S.p.A. will send the Software code to the user

who needs to update. After user receive the file,please decompressing file and cover

the original file in usb flash drive.

Step 4

Insert the usb flash drive into the USB interface.

Step 5

Then turn on DC switch and enter into the online upgrade to the main

menu"5.Software Update"in the LCD display program[6.3(E)].The method to enter

the menu can refer to operation interface of LCD.

Step 6

Input the password,if password is correct,and then begin the update

process,the original password is 0715.

Step 7

System update main DSP, slave DSP and ARM in turns.If main DSP

update success,the LCD will display"Update DSP1 Success", otherwise display

"Update DSP1 Fail";If slave DSP update success,the LCD will display"Update

DSP2 Success",otherwise display "UpdateDSP2 Fail".

Step 8

If Fail,please turn off the DC breaker,wait for the LCD screen

extinguish,then turn on the DC breaker again,then Continue to update from step 5.

Step 9

After the update is completed,turn off the DC breaker, wait for the LCD

screen extinguish,then recover the communication waterproof and then turn on the

DC breaker and AC breaker again,the inverter will enters the running state. User

can check the current software version in Systemlnfo>>3.SoftVersion.

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды