ZCS 1100TL-G3 Скачать руководство пользователя страница 14

Страница: 14 / 69

1.1K~3.3KTL-G3

User manual

- 9 -

(remote) control.

Feeding reactive power into the grid

The inverter is able to produce reactive power and can therefore feed it into

the grid through the setting of the phase shift factor. Feed-in management can be

controlled directly by the grid company through a dedicated RS485 serial interface.

Limiting the active power fed into the grid

The inverter, if enabled can limit the amount of active power fed into the grid

by the inverter to the desired value (Expressed as a percentage).

Self power reduction when grid is over frequency

When the grid frequency is higher than the limited value, inverter will reduce

output power which is necessary for the grid stability.

Data transmission

The inverter or a group of inverters may be monitored remotely through an

advanced communication system based on RS-485 serial interface, or remotely via

the WIFI/GPRS.

Software update

Support usb flash drive local upgrade software and WIFI/GPRS remote

upgrade software.

Electrical block diagram

Figure2-5 Electrical block diagram

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды