ZCS 1100TL-G3 Скачать руководство пользователя страница 60

Страница: 60 / 69

1.1K~3.3KTL-G3

User manual

- 55 -

If it’s incorrect, change it according to Section
6.3 (A) 10.Set Input mode of this manual.

ID29

SwOCPInstan

The grid current is
too high

Internal faults of inverter, turn OFF the “DC

switch”, wait for 5 minutes, then turn ON the
“DC switch”. Check whether the fault is
rectified. If no, please contact technical support.

ID30

SwBOCPInstant

The input current is
too high

Check whether the input current is higher

than the maximum input current of inverters,
then check the input wiring, if both are correct,
please contact technical support.

ID49

ConsistentFault_

VGrid

The grid voltage
sampling value
between the master
DSP and slave DSP
is not consistent

ID49-ID55 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,
then turn ON the “DC switch”.Check whether
the fault is rectified. If no, please contact
technical support.

ID50

ConsistentFault_F

Grid

The grid frequency
sampling value
between the master
DSP and slave DSP
is not consistent

ID51

ConsistentFault_

DCI

The DCI sampling
value between the
master DSP and
slave DSP is not
consistent

ID52

ConsistentFault_

GFCI

The GFCI
sampling value
between the master
DSP and slave DSP
is not consistent

ID53

SpiCommLose

The spi
communication
between the master
DSP and slave DSP
is fault

ID54

SciCommLose

The Sci
communication
between the control
board
communication
board is fault

ID55

RelayTestFail

The relays fault

ID56

PvIsoFault

The insulation
resistance is too
low

Check the insulation resistance between the

PV array and earth(ground), if a short circuit
occurs, rectify the fault.

ID57

OverTempFault_I

The inverter temp
is too high

Ensure the installation position and

installation method meet the requirements of
Section 3.4 of this user manual.

Check whether the ambient temperature of

the installation position exceeds the upper limit.
If yes, improve ventilation to decrease the

ID58

OverTempFault_

Boost

The Boost temp is
too high

ID59

OverTempFault_

The environment

Содержание 1100TL-G3






































































Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды

ZCS 1100TL-G3, Руководство пользователя

Результаты поиска

Содержание 1100TL-G3

Отзывы:

Похожие инструкции для 1100TL-G3

Бренды по названию

Популярные бренды