YOKOGAWA wt1600, Руководство пользователя

Страница: 45 / 162

Commands
5-11
IM 760101-11E
5
Command Function Page
:WAVeform:SRATe? Queries the sampling rate of the retrieved waveform. 5-84
:WAVeform:STARt Sets the output start point of the waveform display data that is transmitted by
“ :WAVeform:SEND? ” or queries the current setting. 5-84
:WAVeform:TRACe Sets the target waveform for the WAVeform:SEND and WAVeform:LENGth
commands or queries the current setting. 5-84
:WAVeform:TRIGger? Queries the trigger position of the retrieved waveform. 5-84
WSETup (Wave SETup) Group
:WSETup? Queries all settings related to the waveform observation. 5-86
:WSETup:POSition? Queries all settings related to the vertical position (GND position) of the
waveform. 5-86
:WSETup:POSition:{UALL|IALL} Collectively sets the vertical position (level of the center position) of the
waveform {voltage|current} of all elements. 5-86
:WSETup:POSition:{U<x>|I<x>} Sets the vertical position (level of the center position) of the waveform
{voltage|current} of the element or queries the current setting. 5-86
:WSETup[:SAMPling] Turns ON/OFF the waveform sampling or queries the current setting. 5-86
:WSETup:TDIV Sets the Time/div value of the waveform or queries the current setting. 5-86
:WSETup:TRIGger? Queries all settings related to the trigger. 5-86
:WSETup:TRIGger:LEVel Sets the trigger level or queries the current setting. 5-86
:WSETup:TRIGger:MODE Sets the trigger mode or queries the current setting. 5-86
:WSETup:TRIGger:SLOPe Sets the trigger slope or queries the current setting. 5-86
:WSETup:TRIGger:SOURce Sets the trigger source or queries the current setting. 5-87
:WSETup:VZoom? Queries all settings related to the vertical zoom factor of the waveform. 5-87
:WSETup:VZoom:{UALL|IALL} Collectively sets the vertical zoom factor of the waveform
{voltage|current} of all elements. 5-87
:WSETup:VZoom:{U<x>|I<x>} Sets the vertical zoom factor of the waveform {voltage|current}
of the element or queries the current setting. 5-87
Common Command Group
*CAL? Executes zero calibration (zero level compensation, same operation as
pressing CAL (SHIFT+MEASURE)) and queries the result. 5-88
*CLS Clears the standard event register, extended event register, and error queue. 5-88
*ESE Sets the standard event enable register or queries the current setting. 5-88
*ESR? Queries the standard event register and clears the register. 5-89
*IDN? Queries the instrument model. 5-89
*OPC Sets a “1” to bit 0 (OPC bit) of the standard event register upon the
completion of the specified overlap command. 5-89
*OPC? ASCII code “1” is returned when the specified overlap command is completed. 5-89
*OPT? Queries the installed options. 5-89
*PSC Sets whether to clear the following registers at power up or queries the current
setting. Clears the register when the value rounded to an integer is not zero. 5-89
*RST Executes the initialization of settings. 5-89
*SRE Sets the service request enable register or queries the current setting. 5-90
*STB? Queries the status byte register. 5-90
*TRG Executes the same operation as when SINGLE (SHIFT+HOLD) is pressed. 5-90
*TST? Performs a self-test and queries the result. 5-90
*WAI Holds the subsequent command until the completion of the specified overlap
operation. 5-90
5.1 Command List