YOKOGAWA DPharp EJXC40A Скачать руководство пользователя страница 108

Страница: 108 / 150

<8. Maintenance>

8-5

IM 01C25W05-01EN

Slide switch

DRS cable

connection port

Integral indicator

Mounting screw

Amplifier cover

Zero-

adjustment

screw

Conduit

connection

Zero-adjustment

screw pin

Press forward

Output terminal cable

DRS output cable

CPU

assembly

DRS cable

connection port

Amplifier cover

CPU assembly

F0803.ai

Low pressure side transmitter (slave)

High pressure side transmitter (master)

Figure 8.3

Removing and Attaching LCD Board

Assembly and CPU Assembly

8.4.2 Replacing the CPU Board Assembly

This subsection describes the procedure for

replacing the CPU assembly. (See Figure 8.3.)

■ Removing the CPU Assembly

1. Remove the cover. If an integral indicator is

mounted, refer to subsection 8.4.1 and remove

the indicator.

2. Turn the zero-adjustment screw to the position

as shown in Figure 8.3.

3. Disconnect the output terminal cable (cable

with brown connector at the end). When doing

this, lightly press the side of the CPU assembly

connector and pull the cable connector to

disengage. (See the upper left of Figure 8.3.)

4. Disconnect the DRS output cable (cable with

white connector at the end).

5. Use a socket driver (width across flats, 5.5mm)

to loosen the two bosses.

6. Carefully pull the CPU assembly straight

forward to remove it.

7. Disconnect the flat cable (cable with white

connector at the end) that connects the CPU

assembly and the capsule.

NOTE

Be careful not to apply excessive force to the

CPU assembly when removing it.

■ Mounting the CPU Assembly

1. Connect the flat cable (with white connector)

between the CPU assembly and the capsule.

2. Connect the output terminal cable (with brown

connector).

NOTE

Make certain that the cables do not get pinched

between the case and the edge of the CPU

assembly.

3. Align and engage the zero-adjustment screw

pin with the groove on the bracket on the CPU

assembly. Then insert the CPU board assembly

straight onto the post in the amplifier case.

4. Tighten the two bosses. If the transmitter is

equipped with an integral indicator, refer to

subsection 8.4.1 to mount the indicator.

IMPORTANT

Confirm that the zero-adjustment screw pin is

placed properly in the groove on the bracket prior

to tightening the two bosses. If it is not, the zero-

adjustment mechanism will be damaged.

5. Replace the cover.

Содержание DPharp EJXC40A























































































































































Результаты поиска

Содержание DPharp EJXC40A

Отзывы:

Бренды по названию

Популярные бренды

YOKOGAWA DPharp EJXC40A, Руководство пользователя

Результаты поиска

Содержание DPharp EJXC40A

Отзывы:

Бренды по названию

Популярные бренды