Yenista Optics OSICS Скачать руководство пользователя страница 7

Страница: 7 / 252

OSICS User Manual

1.1

Product Features.............................................................................................................................................................. 15

1.2

OSICS Mainframe Technical Specifications ........................................................................................................... 16

1.3

Product Overview ............................................................................................................................................................ 17
1.3.1

OSICS Front Panel .......................................................................................................................................... 17

1.3.2

OSICS Rear Panel............................................................................................................................................ 18

1.3.3

OSICS Information and Warning Markings.......................................................................................... 19

2. Installing and Connecting the OSICS Multifunction Platform............................................................. 21

2.1

Unpacking and Installing the OSICS Mainframe ................................................................................................. 21

2.2

Connecting the OSICS Mainframe to a Power Source...................................................................................... 22

2.3

Handling OSICS Modules Into the OSICS Mainframe....................................................................................... 23
2.3.1

Installing an OSICS Module Into the OSICS Mainframe.................................................................. 23

2.3.2

Removing an OSICS Module From the OSICS Mainframe ............................................................. 25

2.4

Connecting Optical Devices to OSICS Modules .................................................................................................. 26

2.5

Installing the Remote Interlock.................................................................................................................................. 27

3. Turning On/Off and Initializing the OSICS Multifunction Platform ................................................... 29

3.1

Turning on the OSICS Multifunction Platform and Accessing the System Status Screen................... 29

3.2

Accessing the OSICS Setup Menus........................................................................................................................... 33

3.3

Checking the OSICS Version ....................................................................................................................................... 34

3.4

Modifying the OSICS Mainframe Password .......................................................................................................... 35

3.5

Turning Off the OSICS Multifunction Platform .................................................................................................... 36

4. Controlling the Optical Output of all OSICS Modules Simultaneously .............................................. 37

4.1

Enabling/Disabling the Light Source of All Modules......................................................................................... 37

4.2

Configuring the Optical Output Power of All Modules.................................................................................... 38
4.2.1

Selecting the Power Unit for All Installed Modules .......................................................................... 38

4.2.2

Setting the Optical Output Power of All Installed Modules .......................................................... 38

4.3

Selecting the Spectral Unit for all Installed Modules ........................................................................................ 39

4.4

Configuring the OSICS Mainframe Modulation .................................................................................................. 40
4.4.1

Setting Up Digital (TTL) Modulation Using the Mainframe Internal Source ........................... 41

4.4.2

Setting Up Digital (TTL) Modulation Using an External Source.................................................... 43

4.4.3

Using the Mainframe as a Modulation Source for External Devices (Synchro Output)...... 44

5. Setting a Working Configuration ........................................................................................................... 45

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды