Yenista Optics OSICS Скачать руководство пользователя страница 16

Страница: 16 / 252

Product Presentation

OSICS User Manual

1.2

OSICS Mainframe Technical Specifications

The following table gives an overview of technical specifications of the OSICS Mainframe.

Detailed specifications of all OSICS modules are detailed in

OSICS User Manual

General Characteristics

Number of slots

Supported pluggable modules

All OSICS modules in any combination

Electrical Specifications

Fuse type

4.0 A 250 V SLOW/(T)

Power Supply

100-240 V AC ±10 %

Power Supply Frequency

50-60 Hz ±5 %

Maximum Power Consumption

120 W

Interfaces

Control Panel

Screen, rotary knob, on/off and control buttons

Remote Control

•

GPIB connector for IEEE 488 communication

•

USB-B connector for RS-232C

communication

•

SubD-9 for remote interlock

Analog Monitoring

Multi-purpose BNC output for current, power or

temperature monitoring of each pluggable

module

Modulation

•

Input:

•

External TTL modulation (Mod. In BNC

connector)

•

Internal TTL modulation (on-board

oscillator)

•

Output: Synchro BNC connector

Environmental Specifications

Equipment Type

Test and measurement

Equipment Location

Indoor use only

Operating Temperature Range

+15 °C to 35 °C (+59 °F to +95 °F) ambient

temperature

Warm up Time (at room temperature) 1 hour (typ.)
Humidity

80 % to 50 % relative humidity

(with maximum operating temperature ranging

from 31 °C to 40 °C)

Maximum Operating Altitude

2000 meters

Physical Specifications

Dimensions (W x H x D)

448 x 145 x 387 mm

Weight

7.2 kg

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды