Yenista Optics OSICS Скачать руководство пользователя страница 54

Страница: 54 / 252

Using the OSICS ATN-HP Module

OSICS User Manual

c. Perform steps a. and b. again with the other digits to modify.
d. Turn the rotary knob clockwise to put the cursor under

ENTER

and press the

knob to validate the new step value.

The

ATN

Unit Setup

menu is automatically displayed.

To modify the wavelength/frequency defined in the

Set

Attenuation

menu (see

section

Setting the Attenuation to a Definite Value, p. 51

), expand the

Step

menu,

move the cursor before the

Step +

Step -

sub-menus and press the knob to step-

adjust the value.

Repeat step 4. until the wanted attenuation value is reached.

6.3

Setting the ATN Wavelength

Subject

The

Set

menu enables you to set the reference wavelength. Each module is factory-

calibrated at different wavelengths depending on the module version (SMF or PMF): see

section

OSICS ATN-HP Technical Specifications, p. 49

Procedure

Access the

ATN Unit Setup

menu (see section

Accessing an OSICS Module Setup

Menu, p. 33

Turn the rotary knob to put the cursor before the

Set

menu and press the knob.

The

Set Wavelength

Set Frequency

menu appears and displays the current value of

wavelength or frequency according to the selected unit.

Figure 27: ATN Unit Setup – Set Wavelength menu

Turn the rotary knob to put the cursor before the wanted value and press it to

validate your selection.
The

Unit Setup

menu is automatically displayed and the wavelength/frequency value

is now set.

Main

EXIT

ATN Unit Setup - Set Wavelength

ESCAPE

▲

Wavelength :

1550 nm

1300 nm

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды