Yenista Optics OSICS Скачать руководство пользователя страница 33

Страница: 33 / 252

Turning On/Off and Initializing the OSICS Multifunction Platform

OSICS User Manual

3.2

Accessing the OSICS Setup Menus

Subject

Each element of the OSICS platform can be configured individually:

•

The OSICS Mainframe setup menu (

Main Setup

menu) enables you to configure all

the operating parameters of the OSICS Mainframe and some system parameters that

affect all installed modules.

•

The OSICS module setup menu (

<Module Name> Setup

menu) enables you to set

the operating parameters of a selected OSICS module.

Procedures

Accessing the OSICS Mainframe Main Setup Menu
1.

From the

System Status

screen, turn the rotary knob to highlight the

Main

tab.

Press the knob to enter the highlighted menu.
The

Main Setup

menu appears.

Accessing an OSICS Module Setup Menu
1.

From the

System Status

screen, turn the rotary knob to highlight the tab

corresponding to the slot number in which the wanted module is installed (see

Figure 1, p. 17

Press the knob to enter the highlighted menu.
The

<Module Name> Setup

menu appears.

Setup Menu

Description

Figure 10: Setup Menu – Examples

Menus/Sub-menus and Symbols

•

►

: indicates the location of the cursor operated using the rotary knob.

To move the cursor, turn the rotary knob.

•

●

: indicates a menu without sub-menus.

To enter this type of menu: turn the rotary knob to put the cursor before the menu

and press the rotary knob.

•

: indicates a menu with one or more sub-menus.
: indicates that the menu is expanded.

•

To expand a menu: turn the rotary knob to put the cursor before the menu and

press the rotary knob.

•

To enter a sub-menu: turn the rotary knob to put the cursor before the sub-menu

and press the rotary knob to enter into it.

Main

EXIT

ECL Unit Setup

ESCAPE

Set Power

Step

●

▲

Calibration

Coherence

●

Analog Out

●

Information

●

Adjust Power

●

Set

●

Modulation

Auto peak find

●

Main

EXIT

Main Setup

ESCAPE

Optical Output : DISABLED

Power

●

▲

Set unit dBm/mW

Set power reference

Modulation

▲

Source

Set frequency

Set unit GHz/nm

●

GPIB address : 10

●

Configuration : STARTUP

▲

Load

Save

Password

●

Information

●

OSICS Mainframe Setup Menu

OSICS ECL Unit Setup Menu

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды