Yenista Optics OSICS Скачать руководство пользователя страница 42

Страница: 42 / 252

Controlling the Optical Output of all OSICS Modules Simultaneously

OSICS User Manual

Step 2 – Set the frequency of the OSICS Mainframe internal modulated-signal:
1.

In the

Main Setup

menu, expand the

Modulation

menu and select the

Set

frequency

sub-menu.

The

Modulation frequency

sub-menu appears and displays the current selected

modulation frequency-value.

Figure 17: Main Setup – Modulation Frequency

Modify the frequency value as follows:
The internal TTL-signal generator can provide a TTL-modulated signal in the range

123 Hz to 1 MHz.
a. Turn the rotary knob to put the cursor under the digit you want to modify and

press the knob to highlight it.

b. Turn the knob clockwise to increase the value or anticlockwise to decrease it and

press the knob to validate the selected digit.

c. Perform steps a. and b. again with the other digits to modify.
d. Turn the rotary knob clockwise to put the cursor under

ENTER

and press the

knob to validate the new frequency value.

The frequency is updated to the "real frequency" as shown in

Figure 18, p. 42

. This

screen displays the current modulation frequency produced by the OSICS Mainframe

oscillator, which may slightly differ from the values you have set.

Figure 18: Main Setup – Modulation Real Frequency

Press the knob to go back to the

Main Setup

menu.

Main

EXIT

Main Setup - Modulation frequency

ESCAPE

▲

Frequency value :

f = 0014700 Hz

Modify the value.

ENTER

Main

EXIT

Main Setup - Modulation frequency

ESCAPE

The real frequency is :

14706 Hz

Please press the knob.

Содержание OSICS





























































































































































































































































Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды

Yenista Optics OSICS, Руководство пользователя

Результаты поиска

Содержание OSICS

Отзывы:

Бренды по названию

Популярные бренды