YATO YT-23300, Руководство пользователя

Страница: 16 / 112

16
EN
O R I G I N A L I N S T R U C T I O N S
porting it. The power switch must be in the o ff position and the power cord plug disconnected from the power source. The device
must not be transported with the pressurised tank.
Observe the maximum pressure of the in fl ated products. Use a pressure gauge (built-in or separate) to control the pressure inside
the in fl ated product. Exceeding the maximum pressure may cause damage to the in fl ated product or even its rupture. Rupturing
the product can cause serious injuries.
Periodically check that the readings of the pressure gauge built into the device match those of the calibrated pressure gauge.
Check the tool for damage before each use. If you notice any cracks, abrasions or other damage, do not use the tool until the
defects are removed.
The device is designed for use with fl exible pressure hoses only. The hoses connected to the device should withstand at least the
pressure that the compressor is capable of generating. Hoses for pressures higher than 7 bar / 0.7 MPa should be equipped with
a protective shell, e.g. in the form of wire ropes.
Before connecting the hose to the device, check that the hose is not damaged. If abrasions, cracks or air leaks of the insulation
are discovered, stop using the damaged hose and replace it with a new hose before commencing work.
Never bend or twist the hose during operation. Bending the hose can reduce its inside diameter even to the point where the air
fl ow stops. This can lead to damage to the hose or even to its rupture, which can result in serious injuries. Bending and twisting
the hose also speeds up hose wear. Never carry the tool holding it by the hose. Do not overtension the hose during operation.
Avoid the creation of long lines for the transfer of compressed air. Shorter lines are easier to control.
All devices and accessories connected to the compressor should withstand at least the pressure that the compressor is capable
of generating.
It is forbidden to adjust or modify the safety valve on your own. The improperly adjusted or modi fi ed safety valve may cause
damage to the product, which may result in serious injury.
Do not use the device as an arti fi cial respiration device, for spraying any substance, or for any other application not described in
the instructions manual. The compressor may only be used to compress air. It is forbidden to compress other gases.
Never point the air stream toward yourself, other people, or animals. Do not use your fi nger or any other part of the body to check
if the device is pumping air.
Make sure that the device is turned o ff before connecting the hose and accessories to the device. Children and pets must not be
near the device when in use. The device is not intended to be used by children.
The device should be used, transported and stored in a vertical position. Using, transporting and storing the device in a position
other than vertical may damage the product.
Recommendations for connecting the device to the power supply
Before connecting the device to the power supply, make sure that the voltage, frequency, and the mains capacity correspond to
the values shown on the device’s rating plate. The plug must fi t into the power socket. It is forbidden to modify the plug or socket
in any manner to make them fi t.
The device must be connected directly to a single mains socket. The supply network circuit should be equipped with a protective
conductor and a protective device of 16 A. When using extension cords, use an extension cord with three wires that can withstand
a 16 A current load.
Avoid contact of the power cord with sharp edges, hot objects or surfaces, including those of the device. During operation, the
power cord must always be fully extended and the position of the power cord must be set so that it does not become an obsta-
cle during product operation. The power cord should not be placed in a manner which would pose a risk of tripping. The power
supply socket should be located in a place where it is always possible to quickly remove the product power cord plug. Always
pull the power cord by the plug housing when unplugging it, never by the cord. It is forbidden to bring the power cable close to a
hot device. If the power cord or the plug is damaged, immediately disconnect it from the mains and contact an authorised service
centre of the manufacturer for replacement. Do not replace the power cord by yourself. Do not use the product with a damaged
power cord or plug. The power cord or plug cannot be repaired and must be replaced with a new one that is free of defects if these
components are damaged.
PRODUCT OPERATION
Preparing for operation
Caution! The procedure described in this section must be carried out with the device disconnected from the power supply. Make
sure that the power cord has been unplugged from the mains socket.
The product must be unpacked by removing all packaging elements. It is recommended to keep the packaging, as it can be helpful
for further transport and storage of the product. Check the product for damage. If any damage is detected, do not use the product
until the damage has been repaired or the damaged components are replaced with new ones that are free of defects.
Product assembly
CAUTION! Before fi rst use, check that the tightness of all screw connections, especially of the screws in the compressor head
and the body, is correct.
A foot, feet (II) or wheels must be screwed into the base of the tank depending on the model. Install the foot or wheel in the hole
in the base with a screw, inserting the screw from below. Use washers and screw on the nut. Screw with a suitable spanner. As-