Polair Systems portable air compressor Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 15

Polair Systems portable air compressor Скачать руководство пользователя страница 1

ROLAIR SYSTEMS

606 S. Lake Street, P.O. Box 346
Hustisford Wisconsin 53034-0346
Phone: 920-349-3281
Sales Fax: 920.349.3691
Service Fax: 920.349.8861

www.rolair.com

PORTABLE

AIR COMPRESSOR

OWNER’S MANUAL

WARNING

COMPRESSOR DISCHARGE AIR MAY CONTAIN HYDROCARBONS AND

OTHER CONTAMINANTS! DO NOT USE DISCHARGE AIR FOR BREATHING!

PARTS

Genuine ROLAIR replacement parts are sold nationwide through a network of authorized dealers and
service centers. Please contact the dealership where your air compressor was purchased or our factory
Customer Service Department if you need help troubleshooting, obtaining parts, or locating an
authorized ROLAIR service representative.

To order replacement parts:

1. Give compressor model number
2.

Give compressor serial number

3.

Name of part

4.

Part number

5.

Quantity required

1
2
3
...
»

Содержание portable air compressor
















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды