Yamaha PW50W 2007 Скачать руководство пользователя страница 46

Страница: 46 / 168

CHK

ADJ

3-14

CHECKING THE FRONT AND REAR BRAKE SHOES/

CHECKING AND ADJUSTING THE STEERING HEAD

2. Check:

Wear indicator
If the lining thickness of a brake shoe is
less than 1.5 mm (0.06 in)

→

Replace the

front or rear brake shoes as a set.
Refer to “FRONT WHEEL, REAR WHEEL
AND BRAKE “in chapter 4.

NOTE:

Be sure to measure the brake lining at the
thinnest portion.

CHECKING AND ADJUSTING THE STEER-
ING HEAD

1. Stand the vehicle on a level surface.

Securely support the vehicle so that there
is no danger of it falling over.

NOTE:

Place the vehicle on a suitable stand so that
the front wheel is elevated.

2. Check:

Steering head
Grasp the bottom of the front fork legs
and gently rock the front fork.
Blinding/looseness

→

Adjust the steering

head.

3. Remove:

Handle protector

Handle
Refer to “STEERING “in chapter 4.

4. Adjust:

Steering head

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Remove the steering stem bolt

, washer

and cap bolt

washer

REAR

5PG-7-10 44

06.5.16, 17:42:38

Содержание PW50W 2007









































































































































































Результаты поиска

Содержание PW50W 2007

Отзывы:

Похожие инструкции для PW50W 2007

Бренды по названию

Популярные бренды

Yamaha PW50W 2007, Руководство по обслуживанию

Результаты поиска

Содержание PW50W 2007

Отзывы:

Похожие инструкции для PW50W 2007

Бренды по названию

Популярные бренды