Yamaha PW50W 2007 Скачать руководство пользователя страница 45

Страница: 45 / 168

CHK

ADJ

3-13

CHECKING THE FUEL HOSE/ADJUSTING THE FRONT AND REAR BRAKE/

CHECKING THE FRONT AND REAR BRAKE SHOES

CHECKING THE FUEL HOSE

1. Check:

Fuel hose

Clack/Damage

→

Replace

CHASSIS

ADJUSTING THE FRONT AND REAR
BRAKE

1. Check:

Brake lever free play

Out of specification

→

Adjust.

2. Adjust:

Brake lever free play

▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼▼

a. Turn the adjuster

in direction

until the specified brake lever free play is
obtained.

After adjusting the brake lever free play,

make sure there is no brake drag.

▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲▲

CHECKING THE FRONT AND REAR
BRAKE SHOES

NOTE:

To remove the front wheel:
Refer to “FRONT WHEEL” in chapter 4.
To remove the rear wheel: See
Refer to “REAR WHEEL” in chapter 4.

Brake lever free play (at the end
of the brake lever)

10.0-20.0 mm (0.39-0.79 in)

Direction

Brake lever free play

is increased.

Direction

Brake lever free play

is decreased.

FRONT

REAR

FRONT

5PG-7-10 43

06.5.16, 17:42:37

Содержание PW50W 2007









































































































































































Результаты поиска

Содержание PW50W 2007

Отзывы:

Похожие инструкции для PW50W 2007

Бренды по названию

Популярные бренды

Yamaha PW50W 2007, Руководство по обслуживанию

Результаты поиска

Содержание PW50W 2007

Отзывы:

Похожие инструкции для PW50W 2007

Бренды по названию

Популярные бренды